Jet Service
Категории каталога
Epson [2]
Lexmark [2]
HP [4]
Brother [2]
Konica Minolta [1]
OKI Data [2]
Samsung [5]
Наши проекты
Форма входа
Поиск
Статистика

Онлайн всего: 1
Гостей: 1
Пользователей: 0
Пятница, 18.07.2025, 14:09
Приветствую Вас Гость | RSS
Главная | Регистрация | Вход
Заправка и восстановление катриджей
Продажа комплектующих и расходных материалов
Обслуживание и ремонт оргтехники
Каталог файлов
Главная » Файлы » Заправка тонером » HP

Remanufacturing the HP LaserJet P4014 64a Cartridge
[ ] 13.03.2009, 15:26
Remanufacturing the HP LaserJet P4014 64a Cartridge


Image

    • 64a cartridge is compatible with LaserJet P4014/P4015/P4515
    • 64x cartridge is compatible with LaserJet P4015/4515

Step 1 - To remove the drum shutter

    • From the none spring side of the cartridge lift out the metal arm of the drum shutter

    Image


    • From the spring side of the cartridge pull out the plastic arm

    Image


    • Using a small flat blade screwdriver, push the plastic pin back to lift out the drum shutter arm

    Image

    Image


Step 2 – Remove the end plates

    • There are 5 screws on both sides of the cartridge which must be removed

    Image

    Image


    • Lift away the end caps which separates the two sections of the 64a cartridge

    Image

Step 3 – The OPC Drum section

    • Remove one screw and lift out the white plastic end plate, the OPC drum lifts out from the unit.

    Image
    Image



    • Remove the PCR roller and clean the roller with soft damp (with water) cotton cloth. Allow to dry.

    Image


    • Remove and clean wiperblade

    Image



    • Replacing the OEM OPC unit is optional – we suggest for best print image quality the OPC drum should always be replaced. If you do replace the OPC drum, it’s also advisable the wiperblade is also replaced.
    • When replacing the PCR roller it is advisable to ‘dab’ the black contact housing for the PCR roller with a small amount of contact grease.

    Image

Step 4 – The Hopper unit

    • Remove the plastic double pin from the gear end of the magnetic roller.

    Image


    • Remove the white gear from the end of the magnetic roller

    Image


    • Lift out the metal pin from the other side of the cartridge

    Image


    • Remove one screw and lift out the end plate

    Image


    • Lift out the magnetic roller – we suggest cleaning the magnetic roller with compressed air only.

    ImageImage


    • Remove the two larger screws to release the doctor-blade. Clean the doctor-blade – we suggest wiping clear with a soft damp (with water) cotton cloth.


    ImageImage



Step 5 - Refill with Toner The AQC Group replacement toner for the HP 64a type cartridge is currently in development and further information will be available shortly.

Step 6 - Remove and replace the cartridge chip

    • Place a small flat blade screwdriver underneath the edge of each side of the plastic holding the chip in place and gently prise away the leading tip.
    • Lift out the old chip and replace with new compatible replacement

    ImageImage




Image



Download this guide in .PDF format here
Категория: HP | Добавил: denisoft
Просмотров: 1180 | Загрузок: 0 | Комментарии: 1 | Рейтинг: 0.0/0 |
Всего комментариев: 0
Имя *:
Email *:
Код *:
Copyright Exclusive Group™ © 2025
Хостинг от uCoz